# Latitude and Longitude on a Sectional Chart

> Read and plot coordinates, compare north/east position, and convert decimal minutes to seconds or decimal degrees with a worked study grid.

- Source: https://firstsolo.ai/blog/latitude-longitude-sectional-chart
- Author: Sam Whitaker, Student Pilot
- Published: 2026-11-20
- Updated: 2026-11-20
- Last reviewed: 2026-11-20

To read latitude and longitude on a sectional chart, identify the labeled coordinate lines, determine the tick interval, and interpolate the point between them. Latitude gives north or south position; longitude gives east or west position, with hemisphere letters preserved. Check the coordinate format before transferring the result, because decimal minutes and decimal degrees describe angles differently.

| Key fact | What to remember | Source |
| --- | --- | --- |
| Latitude | Angular position north or south of the equator | [FAA PHAK Chapter 16, p. 16-3](https://www.faa.gov/sites/faa.gov/files/18_phak_ch16.pdf) |
| Longitude | Angular position east or west of the prime meridian | [PHAK pp. 16-3–16-4](https://www.faa.gov/sites/faa.gov/files/18_phak_ch16.pdf) |
| Parallels | Lines of latitude; follow their printed values | [PHAK Figure 16-4](https://www.faa.gov/sites/faa.gov/files/18_phak_ch16.pdf) |
| Meridians | Lines of longitude that converge toward the poles | [PHAK Figure 16-4](https://www.faa.gov/sites/faa.gov/files/18_phak_ch16.pdf) |
| Format matters | Degrees, minutes and seconds differ from decimal degrees | [FAA coordinate-format help](https://oeaaa.faa.gov/oeaaa/oe3a/ng-shared/components/help/coordinate-format.html) |
| Distance relationship | One minute of latitude is approximately one nautical mile | [NOAA nautical-mile explanation](https://oceanservice.noaa.gov/facts/nautical-mile-knot.html) |

## What is the difference between latitude and longitude?

Latitude measures north or south position, while longitude measures east or west position. The direction a line runs is different from the direction its numerical value measures.

A parallel of latitude runs around the Earth in an east–west direction, but its label tells you how far north or south it lies. A meridian runs between the poles, but its longitude label tells you how far east or west it lies. Saying “the horizontal line must be longitude because it goes east–west” confuses those two ideas.

On the north-up local schematic below, north latitude increases upward. West longitude becomes smaller toward the right because the point is moving east, closer to the prime meridian. Those relationships come from the hemisphere labels, not from the size of the printed number alone.

![In this north-up Northern and Western Hemisphere diagram, north latitude increases upward and west longitude leftward](https://s3.doublegis.com/firstsolo/blog/latitude-longitude-sectional-chart/latitude-longitude-direction-check.svg?v=8afc71b2)

*Original direction diagram for a local Northern and Western Hemisphere example. The arrows describe increasing coordinate values; they are not a heading or distance scale.*

## How do you identify the coordinate ticks on a sectional?

Read two labeled values and count the spaces between them before assigning a value to a tick. A longer line, a bold mark or an unlabeled tick is not enough to establish the interval by itself.

For example, an interval from 39°40′N to 39°50′N spans ten minutes of latitude. If it is divided into ten equal spaces, each space represents one minute. Five spaces would instead represent two minutes each. Count spaces between marks, rather than counting both endpoint marks as extra intervals.

Follow the actual chart’s printed graticule and nearby labels. Do not borrow a tick scale from another figure, a cropped screenshot or the edge of your ruler. Zooming changes the displayed size; it does not change the angular interval between coordinate lines.

The [FAA Chart Users’ Guide](https://www.faa.gov/air_traffic/flight_info/aeronav/digital_products/aero_guide/) is the official reference for chart depictions. Start with the [sectional chart reading guide](https://firstsolo.ai/blog/how-to-read-a-sectional-chart) if the other symbols make the coordinate grid hard to isolate.

## How do you read a point between labeled lines?

Bracket latitude and longitude separately, interpolate each value, then write the pair with its hemisphere letters. Our fictional point P lies in a box bounded by 39°40′N and 39°50′N, and by 105°30′W and 105°20′W.

The diagram explicitly divides each ten-minute interval into one-minute spaces. P is 3.5 minutes north of the lower latitude line, so its latitude is 39°43.5′N. It is six minutes east of the left longitude line. Moving east reduces west longitude: 30′ − 6′ = 24′, giving 105°24.0′W.

Therefore P is **39°43.5′N, 105°24.0′W**. Check the bounds before accepting it: 43.5 lies between 40 and 50, and 24 lies between 20 and 30. A longitude of 105°36′W would be outside this box and west of its left boundary.

![Point P is 39 degrees 43.5 minutes north and 105 degrees 24 minutes west in a fictional one-minute coordinate grid](https://s3.doublegis.com/firstsolo/blog/latitude-longitude-sectional-chart/sectional-coordinate-grid-example.svg?v=8e17d9a6)

*Original local schematic, not an operational sectional or an exact chart projection. Every small space represents 1′; the unequal drawing dimensions do not represent equal ground distances.*

The point is an arithmetic example, not a real checkpoint identification. A location is useful in flight planning only when you have connected it to the correct current chart information and intended feature.

## How do you plot a supplied coordinate on the chart?

Reverse the reading process: locate the latitude, locate the longitude, then mark their intersection. Keep the chart references separate until both have been checked.

To plot P, begin 3.5 minutes north of 39°40′N and follow that latitude across the local box. Then locate 105°24′W between the labeled west-longitude lines. Their intersection should fall below the 39°45′N line and east of 105°25′W. That rough placement provides a second check on the detailed measurement.

Use a straightedge or an appropriate plotter carefully, following the printed grid rather than assuming the paper edge supplies true north. Recheck the plotted point against nearby features. A correct pair can still be assigned to the wrong airport symbol, landmark or chart excerpt if you skip that identification step.

## How do degrees, minutes and seconds convert?

One degree contains 60 angular minutes, and one angular minute contains 60 seconds. Decimal minutes are a fraction of a minute; decimal degrees are a fraction of a whole degree.

For P’s latitude, 43.5′ means 43′ plus 0.5′. Multiplying the fractional minute by 60 gives 30″, so 39°43.5′N becomes 39°43′30″N. It does not become 39°43′50″N. The decimal digit is not a count of seconds.

To convert degrees and decimal minutes to decimal degrees, use degrees + minutes ÷ 60. P’s latitude is 39 + 43.5 ÷ 60 = 39.725°. Its west longitude has magnitude 105 + 24 ÷ 60 = 105.4°. In the signed decimal convention used here, north and east are positive; south and west are negative.

| Format | Latitude of P | Longitude of P |
| --- | --- | --- |
| Degrees and decimal minutes | 39°43.5′N | 105°24.0′W |
| Degrees, minutes and seconds | 39°43′30″N | 105°24′00″W |
| Signed decimal degrees | +39.725° | −105.400° |

The [FAA’s format examples](https://oeaaa.faa.gov/oeaaa/oe3a/ng-shared/components/help/coordinate-format.html) show DMS and signed decimal coordinates. For a DMS conversion, calculate the magnitude as degrees + minutes ÷ 60 + seconds ÷ 3,600, then apply the hemisphere sign to the whole result. Do not make only the degree term negative while adding positive minutes to it.

![39 degrees 43.5 minutes north converts to 39 degrees 43 minutes 30 seconds north and positive 39.725 decimal degrees](https://s3.doublegis.com/firstsolo/blog/latitude-longitude-sectional-chart/coordinate-format-conversion.svg?v=fe82b633)

*Original calculation for P. West longitude receives the negative sign after its full magnitude is converted; match the destination field’s format and coordinate order.*

Read the requested entry format before typing. A pair of latitude/longitude fields, a single signed pair and a longitude-first mapping field are different interfaces. Preserve the order specified by the field labels rather than assuming every tool uses the same order.

## How do you compare which point is north or east?

Compare the coordinates within their stated hemispheres, taking particular care with west longitude. In our local Northern and Western Hemisphere example, a larger north latitude is farther north, while a smaller west-longitude magnitude is farther east.

Suppose Q is 39°44.0′N, 105°22.0′W. Compared with P at 39°43.5′N, 105°24.0′W, Q is north because 44.0′ exceeds 43.5′, and east because 22.0′W is closer to the prime meridian than 24.0′W. Q is northeast of P.

This simple comparison stays within one degree and hemisphere. If values cross a degree boundary, normalize them before comparing: 39°59′N is south of 40°01′N even though 59 is larger than 01. If an example crosses a hemisphere boundary or the international date line, do not extend a local “bigger means west” shortcut without considering that geometry.

## Can coordinate minutes be used as a distance scale?

Latitude minutes provide an approximate north–south distance relationship, but longitude minutes do not have the same ground length at every latitude. The meridians converge toward the poles, so their east–west separation changes with latitude.

[NOAA explains](https://oceanservice.noaa.gov/facts/nautical-mile-knot.html) the nautical mile’s relationship to latitude and defines the international nautical mile as exactly 1,852 meters. For basic chart study, one minute of latitude is approximately one nautical mile. It is an angular minute, not a minute of elapsed flying time.

Do not assume two points separated by one minute of longitude are one nautical mile apart. For a route distance, use the chart’s proper distance scale or an appropriate plotting tool. Our rectangular teaching grid is deliberately not a measured map: counting drawing pixels would not establish distance, bearing or a safe route.

## What checks prevent the common coordinate mistakes?

Check hemisphere, interval, bounds, format and feature identity before carrying a coordinate into a plan. These checks catch different mistakes, so a plausible-looking number is not enough.

Say the full pair aloud with its units: “39 degrees, 43.5 minutes north; 105 degrees, 24 minutes west.” Confirm that each value lies within its labeled interval, that the seconds or minutes have not been mistaken for decimal degrees, and that the selected feature is the one requested.

Coordinate position also differs from magnetic heading. Do not apply magnetic variation to latitude or longitude. The [heading-conversion guide](https://firstsolo.ai/blog/magnetic-variation-and-deviation) explains that separate reference change, while the [pilotage guide](https://firstsolo.ai/blog/pilotage-and-dead-reckoning) connects chart features with observed progress.

Under [14 CFR 91.103](https://www.ecfr.gov/current/title-14/section-91.103), the pilot in command’s preflight duty extends to the available information concerning the flight. Reading one coordinate does not establish the route’s terrain clearance, airspace access, weather suitability or aircraft performance.

## Check yourself

**A point is halfway from 39°40′N to 39°50′N and 3′ east of 105°30′W. What is its coordinate?**

39°45′N, 105°27′W. Half of the ten-minute latitude interval is five minutes north of 40′. Moving three minutes east from 30′W reduces the west-longitude minutes to 27′. It does not increase them to 33′W.

**Convert P’s latitude, 39°43.5′N, to DMS and signed decimal degrees.**

39°43′30″N and +39.725°. The fractional 0.5 minute becomes 30 seconds; 43.5 ÷ 60 = 0.725 degree. Writing 39.435° or treating .5′ as 50″ would change the location.

**Q is 39°44′N, 105°22′W. Is it northeast or northwest of P at 39°43.5′N, 105°24′W?**

Northeast. Q’s north latitude is larger, and its west-longitude magnitude is smaller. In this local western-hemisphere comparison, moving from 24′W to 22′W moves east, not west. No distance or route clearance follows from that direction comparison.

## Frequently asked questions

**Are latitude lines the north–south lines?**

No. Parallels of latitude run east–west around the Earth, while their values measure north or south position. Meridians of longitude run between the poles and measure east or west position.

**Is 39°43.5′ the same as 39.435°?**

No. The first uses decimal minutes; the second uses decimal degrees. Convert 43.5 minutes by dividing by 60, giving 39.725 degrees for the first value.

**Does showing more decimal places make a chart reading more accurate?**

No. Extra digits do not create detail absent from the source chart, point definition or measurement. Match the requested precision and verify the coordinate format, hemisphere, feature and applicable source reference.

**Can FirstSolo.ai approve my coordinate or issue an endorsement?**

No. FirstSolo.ai is solely a study tool. It does not approve flights or issue FAA knowledge-test endorsements, now or in the future. Review real chart work and flight planning with your instructor and current source information.

## Sources and next steps

The FAA [PHAK Chapter 16](https://www.faa.gov/sites/faa.gov/files/18_phak_ch16.pdf), pp. 16-3–16-4 and Figure 16-4, explains parallels and meridians. Use the current [FAA Chart Users’ Guide](https://www.faa.gov/air_traffic/flight_info/aeronav/digital_products/aero_guide/) for chart depictions, [FAA format help](https://oeaaa.faa.gov/oeaaa/oe3a/ng-shared/components/help/coordinate-format.html) for coordinate examples, and [NOAA](https://oceanservice.noaa.gov/facts/nautical-mile-knot.html) for the nautical-mile relationship. The [Private Pilot Airplane ACS](https://www.faa.gov/training_testing/testing/acs/private_airplane_acs_6.pdf), I.D.S2 and VI.A, places chart use within flight planning and navigation.

Return to the [Navigation hub](https://firstsolo.ai/blog/how-to-read-a-sectional-chart), separate coordinates from [heading conversions](https://firstsolo.ai/blog/magnetic-variation-and-deviation), or connect landmarks with [pilotage and dead reckoning](https://firstsolo.ai/blog/pilotage-and-dead-reckoning). Then [practise Navigation VI.A](https://firstsolo.ai/topics/VI.A) on FirstSolo.ai. All plotted points and drawing coordinates in this guide are fictional study examples.
