VOR Navigation Explained: Radials, CDI, TO/FROM
VOR navigation explained in one rule: keep position, selected course and heading separate. A radial extends from the station, the CDI shows deviation from the selected course line, and TO/FROM describes that course’s relationship to the station. From the 090° radial, centered 090° FROM or 270° TO describes the same east-side position without revealing the airplane’s heading or motion.

On this page
- Which VOR facts should you learn first?
- What is a VOR radial, and which way does it point?
- What do the OBS and CDI actually tell you?
- Does TO mean the airplane is flying toward the station?
- When can normal needle sensing become reversed?
- What changes as you pass the station?
- What should you check before trusting a VOR indication?
- Does VOR also give distance or replace other navigation?
- Check yourself
- Frequently asked questions
- Sources and next steps
Which VOR facts should you learn first?
Learn what each indication describes before interpreting a navigation problem.
| Item | Meaning | Important limit |
|---|---|---|
| Radial | Magnetic bearing extending outward from the station | Position reference, not aircraft heading |
| OBS | Omnibearing selector; selects a course | Turning it does not move the aircraft |
| CDI needle | Left/right deviation from the selected course line | Not a heading indicator or mileage scale |
| TO/FROM | Relationship of the selected course to the station | Not a sensor of actual direction of travel |
| Typical conventional VOR dot spacing | Approximately 2° per dot | VOR mode; do not transfer this to other modes |
| Positive identification | Morse identifier or proper automatic voice identification | An expected database label alone is not received identification |
| VOR alone | Bearing information | Distance requires an appropriate separate source |
Sources: FAA PHAK Chapter 16, pages 16-22–16-26 and AIM 1-1-3. Examples below assume a correctly selected VOR source, valid identification and a usable signal, away from the station’s unreliable overhead area.
Use the sectional-reading guide to connect a station and its published information with the chart. This article teaches conventional VOR orientation; follow the actual receiver’s manual for its controls and annunciations.
What is a VOR radial, and which way does it point?
A radial extends outward from the station, regardless of the airplane’s heading or direction of travel.
Think of the station at the center of a wheel. The 090° radial extends east of the station; the 270° radial extends west. An airplane east of the station is on the 090° radial whether its nose points east, west or another direction. Naming its position does not prescribe a turn.
For a direct course toward the station from that east-side position, the reciprocal is 270°. Add or subtract 180° to find the opposite course: 090° and 270° share the same line but opposite directions. Likewise, the reciprocal of 225° is 045°, keeping the result within the compass circle.
The PHAK radial definition uses magnetic bearings from the station. Keep that reference separate from a true course measured against a chart meridian and from a compass heading affected by wind correction and compass deviation. Do not add a remembered variation correction to a published radial without understanding the references involved.
Original magnetic-reference schematic. The position marker has no heading or motion arrow; both instrument summaries describe the same location. No real station or flight route is shown.
What do the OBS and CDI actually tell you?
The OBS selects a course, and the CDI indicates angular deviation from its course line.
Read the course selector, left/right needle and TO/FROM together. Centering the needle while rotating the OBS can identify the radial with a FROM indication, or its reciprocal with a TO indication. A centered needle alone leaves that distinction unresolved.
The PHAK’s conventional VOR illustration, Figure 16-29, shows approximately 2° between dots in VOR mode. In the explicitly conventional VOR example below, two dots represent approximately 4° of angular deviation, not four nautical miles. The same angular error spans more lateral distance farther from the station.
Do not carry that dot value into a localizer, GPS or another navigation mode. Electronic displays can change sensitivity with their source and mode. Check the selected NAV source, applicable annunciations and equipment instructions before interpreting a needle.
A CDI is also not an RMI bearing pointer. Its needle is not simply an arrow aimed at the station. An HSI presents course information with a heading reference, but that does not remove the need to confirm the source, selected course and validity.
Original VOR-mode scale example, not a cockpit screenshot or turn command. The selected course, TO/FROM and heading must also be known before choosing an intercept.
Does TO mean the airplane is flying toward the station?
No: TO describes the selected course, not measured airplane motion.
At the same east-side position on the 090° radial, selecting 270° gives a centered needle with TO, while selecting 090° gives a centered needle with FROM. Rotating the OBS changes the displayed relationship without changing the airplane’s location or heading.
| Fictional position | Selected course | Centered indication | Course relationship |
|---|---|---|---|
| East, on radial 090° | 090° | FROM | Eastward course away from station |
| East, on radial 090° | 270° | TO | Westward course toward station |
| West, on radial 270° | 090° | TO | Eastward course toward station |
| West, on radial 270° | 270° | FROM | Westward course away from station |
These four cases assume valid conventional VOR indications on the stated course line. None supplies aircraft heading, groundspeed, distance or current track. The selector can produce TO even while the airplane points away from the station.
For an inbound leg along the 090° radial, describe the task as tracking the radial inbound on its reciprocal 270° course. This avoids calling the inbound leg “the 270 radial,” which would place the airplane on the opposite side of the station.
When can normal needle sensing become reversed?
On a conventional CDI, using the reciprocal course selection for the direction you intend to fly can reverse the apparent left/right guidance.
The PHAK’s VOR tips, page 16-26, explain the problem with flying toward a station using FROM, or away using TO. A memorized “turn toward the needle” instruction is not sufficient when the setup is wrong.
First identify the station, your position and the desired inbound or outbound leg. Select the intended course, confirm the expected TO/FROM indication and compare it with the heading and chart. Then use the aircraft’s applicable intercept and tracking technique. Do not keep rotating the OBS to make an unwanted deflection disappear while claiming to hold an assigned course.
Wind adds another distinction: course is the intended path over the ground, while heading is where the nose points. A wind-corrected heading can differ from the selected course while maintaining the desired track. The E6B wind-triangle guide explains that relationship.
What changes as you pass the station?
For a straight passage through the station area on the same selected course, a stable inbound TO indication becomes FROM after passage.
In an idealized eastbound example, an airplane west of the station selects 090° and sees TO. After continuing east beyond the station, that same 090° selection corresponds to FROM. The airplane is then on the 090° radial; its earlier inbound position was on the 270° radial.
Near and above the station, the needle can fluctuate and indications become unreliable. The AIM’s service-volume guidance notes a generally unusable conical area overhead. Do not treat momentary needle motion as a precise position, exact overhead crossing or a command for aggressive corrections. Confirm passage using the appropriate indications and other available navigation information.
If continuing on the same straight course after passage, the PHAK explains that the course selector need not be reversed merely because TO changes to FROM. A different planned outbound course requires its own selection and intercept.
Original three-stage schematic, not to scale. The same selected course is retained; the overhead segment deliberately supplies no reliable needle indication or exact passage point.
What should you check before trusting a VOR indication?
Confirm the intended source, positive station identification, signal validity and current facility information.
The AIM 1-1-3 identification guidance distinguishes received Morse identification or the proper recorded automatic voice identification from unrelated voice traffic. Equipment that automatically decodes the received identifier can provide verification; equipment that merely displays an expected database name does not do the same job. Know which function your receiver provides.
Check navigation warning flags and applicable NOTAMs. The AIM directs pilots to disregard apparently valid indications from a transmitter identified as unusable or inoperative. A centered needle does not overrule that information.
VOR signals have line-of-sight limitations. Reception depends on location, terrain, altitude and the applicable service volume or published procedure. Use current Chart Supplement information and restrictions; there is no single guaranteed range for every VOR. The current AIM includes additional service-volume classes beyond the older T/L/H teaching table.
Connect this with the preflight weather briefing checklist: weather, terrain and route conditions still matter when the navigation equipment is working. A radio indication is information, not permission to enter airspace or proof of a suitable flight path.
Does VOR also give distance or replace other navigation?
A VOR alone supplies bearing information; distance and independent position checks need their appropriate sources.
VOR/DME and VORTAC facilities can support compatible DME equipment, but a VOR receiver alone does not become a distance receiver. AIM 1-1-7 explains that DME measures slant-range distance, which differs from horizontal ground distance. Confirm what source any displayed distance actually uses.
For study, redraw the station, position and selected course before interpreting the display. Use visual references and other appropriate information to cross-check navigation. These original exercises align with Private Pilot ACS PA.VI.B.K1, covering ground-based navigation identification, orientation, course determination and signal integrity.
Check yourself
You are southwest of a fictional VOR on radial 225°. What direct inbound course centers the conventional indicator with TO?
Show the answer
The reciprocal is 045°: 225° minus 180° equals 045°. With a valid signal and the stated on-radial position, selecting 045° gives centered TO. The airplane remains on radial 225° until its position changes; its heading and wind correction are not supplied.
You are east of the station, with 270° selected, centered CDI and TO. Does that prove a westbound heading or motion?
Show the answer
No. It identifies the westward selected course toward the station from that position. The conventional indicator does not sense aircraft heading or direction of travel. Selecting 090° at the same position would instead give centered FROM without moving the aircraft.
In the illustrated VOR mode, the needle is two dots from center. Is that four nautical miles off course?
Show the answer
No. At approximately 2° per dot, two dots indicate about 4° of angular deviation. That is not a fixed mileage value, and the dot sensitivity must not be transferred to a different source or mode. The indication alone also does not choose a safe intercept heading.
Frequently asked questions
Can I be on a radial while flying toward the station?
Yes. A radial names the magnetic bearing from the station to your position. An airplane on radial 090° can track inbound on course 270° while still occupying radial 090° until it reaches the station area.
Does a centered CDI prove that the setup is correct?
No. Confirm the source, received station identification, selected course, TO/FROM, signal validity and current restrictions. A centered needle by itself establishes neither the intended leg nor permission or suitability for a flight.
Is a 30-day VOR check required for every VFR flight?
The specific rule in 91.171 governs civil aircraft operated under IFR using VOR navigation. It provides an approved maintenance/check procedure alternative or an operational check within the preceding 30 days within specified limits. It is not a blanket 30-day VFR requirement; reliable equipment and applicable aircraft requirements still matter.
Can FirstSolo.ai approve a flight or issue an endorsement?
No. FirstSolo.ai is solely a study tool. It does not issue FAA endorsements or flight approvals now or in the future; use current official information, aircraft instructions and qualified instruction for real operations.
Sources and next steps
- FAA PHAK Chapter 16: radials, OBS/CDI, sensing, wind correction and station passage, especially pages 16-22–16-26.
- FAA AIM, Chapter 1 Section 1: VOR identification, DME and current NAVAID service-volume guidance.
- FAA Chart Supplement: facility data and restrictions.
- 14 CFR 91.171: VOR equipment checks for IFR operations.
- Private Pilot Airplane ACS: Task VI.B, Navigation Systems and Radar Services.
Return to how to read a sectional chart, review wind-triangle calculations, and connect your route with the preflight briefing checklist. Then practise navigation systems with FirstSolo.ai.

About the author
Ellie Navarro, Student PilotEllie is a student pilot working toward her private pilot certificate in a Cessna 172 near Austin, Texas. She writes up each part of the FAA written the way it finally made sense to her, with the FAA source for every rule.
Last reviewed Nov 16, 2026All guides by EllieKeep going
Start here · NavigationHow to Read a Sectional Chart: Student Guide
Latitude and Longitude on a Sectional Chart
Read and plot coordinates, compare north/east position, and convert decimal minutes to seconds or decimal degrees with a worked study grid.
Sam Whitaker · Nov 20, 2026 · 8 min read
Magnetic Variation and Deviation: Heading Guide
Convert true, magnetic and compass headings with labeled examples, reverse checks and an aircraft compass-card reading exercise.
Ellie Navarro · Nov 18, 2026 · 8 min readA fresh question from the FAA references every time, graded by an AI DPE
Start with 50 free credits.
Start free