Weight and Balance Calculation: CG Step by Step
A weight and balance calculation multiplies each load's weight by its arm, adds the moments, then divides total moment by total weight to locate the center of gravity (CG). Check both total weight and CG against the actual airplane's limitations throughout the flight. Arithmetic alone does not establish an acceptable loading.

On this page
- What weight-and-balance facts should you know?
- Which aircraft records and loading inputs do you need?
- What do datum, arm and moment look like together?
- How do you calculate CG step by step?
- How do you know whether that CG is within limits?
- What if the worksheet uses moment divided by 1,000?
- How does fuel burn change the calculation?
- Which mistakes should you catch before accepting the result?
- Check yourself
- Frequently asked questions
- Sources and review
- What should you practice next?
This guide works a fictional loading example, keeps the units visible and recalculates after fuel burn. For the broader planning sequence, start with the aircraft performance hub.
What weight-and-balance facts should you know?
Know the reference, units and required checks before entering numbers.
| Item | Meaning or calculation | Primary source |
|---|---|---|
| Datum | Manufacturer's reference from which arms are measured | PHAK Chapter 10 |
| Arm | Horizontal distance from datum to an item's CG; preserve its sign | PHAK definitions |
| Moment | Weight × arm; lb × in gives lb-in | PHAK computation method |
| Loaded CG | Total moment ÷ total weight, in compatible units | PHAK Chapter 10 |
| Moment index | A scaled moment; read the chart's divisor before using it | FAA Weight & Balance addendum |
| Final assessment | Check loading limits and changes throughout the flight | 91.9 and ACS Task I.F |
An arm is a distance, a moment combines weight and distance, and CG is a location. Treating those columns as interchangeable produces a plausible-looking but wrong answer.
Which aircraft records and loading inputs do you need?
Use current data for the specific airplane, plus the actual intended load.
The FAA's PHAK weight-and-balance chapter warns that equipment changes can make an airplane's empty weight different from a handbook's sample. Start with the applicable aircraft weight-and-balance record, equipment information, POH/AFM and supplements. Another airplane of the same model is not a substitute.
Identify what the recorded empty-weight definition already includes. Do not add oil, unusable fuel or installed equipment twice. Then account for occupants, baggage, usable fuel and other load items using the applicable loading stations and instructions.
Use measured or otherwise reliable weights. Distinguish pounds from kilograms, inches from another arm unit, and fuel volume from fuel weight. For real planning, use the fuel-weight conversion specified by the applicable data. The example below supplies fuel in pounds so no gallons-to-weight assumption is hidden.
Before calculating, confirm the limits you will eventually check: applicable total-weight limits, forward and aft CG limits, individual baggage or station limits, and any relevant loading restrictions. The Private Pilot ACS, Task I.F, expects weight and balance to remain within limits through all phases of flight.
What do datum, arm and moment look like together?
Moment combines the size of a load with its distance from the chosen reference.
In the FAA's conventional longitudinal examples, locations aft of datum have positive arms and locations forward have negative arms. Follow the actual airplane's reference and sign convention. Do not choose a new datum partway through a worksheet or substitute distance from the nose unless that is the specified reference.
For a hypothetical 40-pound bag at a positive 95-inch arm, the moment is 40 × 95 = 3,800 lb-in. An equally heavy item at a different arm has a different moment.
Original arithmetic example, not a real aircraft station or loading limit. The schematic is not to scale; all arms must use the same datum and units.
The PHAK computational method adds the moments of all items, then divides by total weight. It does not take the simple average of the arms.
How do you calculate CG step by step?
Multiply each weight by its arm, total both weight and moment, then divide the totals.
Every input below is fictional training data. No airplane model, approved envelope, maximum weight or baggage limit is represented. The given basic-empty-aircraft entry is assumed complete for this exercise; usable fuel and the other listed loads are additional items.
| Item | Weight (lb) | Arm (in) | Moment (lb-in) |
|---|---|---|---|
| Basic empty aircraft, given | 1,200 | 40 | 48,000 |
| Front occupants, combined | 360 | 37 | 13,320 |
| Rear occupants, combined | 160 | 73 | 11,680 |
| Baggage | 40 | 95 | 3,800 |
| Usable fuel | 240 | 48 | 11,520 |
| Total | 2,000 | Not added | 88,320 |
- Multiply each row: for example, 360 lb × 37 in = 13,320 lb-in.
- Add the weights: 1,200 + 360 + 160 + 40 + 240 = 2,000 lb.
- Add the moments: 48,000 + 13,320 + 11,680 + 3,800 + 11,520 = 88,320 lb-in.
- Divide: 88,320 lb-in ÷ 2,000 lb = 44.16 in.
The calculated CG is 44.16 inches aft of this fictional datum. The arm values themselves are not added to find CG; larger weights contribute more to the result.
The calculation supplies a weight-and-CG pair, not an in-limits result. No approved envelope or operating limit is supplied for this fictional example.
Keep sufficient precision through the calculation and round only as the applicable instructions permit. A rounded number near a boundary is not a reason to ignore the boundary.
How do you know whether that CG is within limits?
Compare the calculated loading with the actual airplane's applicable envelope and limitations.
Find the permitted CG range for the calculated weight and operating category. Some presentations use CG location; others use total moment or a moment index. Read the axes and units rather than putting 44.16 inches onto a graph that expects moment/1,000.
Check the weight limit as well as the CG boundary and any separate station limits. Being below maximum weight does not establish acceptable CG. Conversely, a CG inside an envelope does not authorize an excessive total weight or baggage load.
14 CFR 91.9 requires compliance with the specified operating limitations. Because this example supplies no approved limits, it cannot answer whether a real flight is permitted.
Weight-and-balance compliance also does not establish adequate takeoff or climb performance for today's conditions. Connect the loading with the density-altitude guide and the applicable POH/AFM performance calculations.
What if the worksheet uses moment divided by 1,000?
Keep scaled moments and full moments consistent before dividing by weight.
The FAA's October 2025 Weight & Balance Handbook addendum explains the moment-index convention. If this example's total moment is shown as 88.32 under “moment/1,000,” it represents 88,320 lb-in.
Restore the scale when calculating CG: 88.32 × 1,000 ÷ 2,000 = 44.16 inches. Dividing 88.32 directly by 2,000 would lose the factor of 1,000. Another worksheet may use a different divisor; its labels control.
How does fuel burn change the calculation?
Subtract both the burned fuel's weight and its moment, then recalculate CG.
Continue the fictional example. Assume 120 pounds of fuel are burned and the fuel arm remains fixed at 48 inches for this exercise:
- Fuel moment removed: 120 × 48 = 5,760 lb-in.
- Remaining weight: 2,000 − 120 = 1,880 lb.
- Remaining moment: 88,320 − 5,760 = 82,560 lb-in.
- New CG: 82,560 ÷ 1,880 = approximately 43.91 in.
The direction is specific to this example: fuel is removed from aft of the initial CG. Actual fuel-moment data and loading limits must be checked throughout the flight.
Here CG moves forward because the removed fuel was aft of the initial 44.16-inch CG. Fuel burn does not always move CG forward or always move it aft; tank location and the actual fuel-moment relationship matter.
For a real airplane, use its fuel data, including any variation with quantity. Account for the applicable ramp, taxi, takeoff, inflight and landing conditions and limits. ACS Task I.F.S1 specifically includes remaining within weight-and-balance limits in all flight phases. Lower weight alone does not prove the new CG is acceptable.
Which mistakes should you catch before accepting the result?
Check the data, units and limits as carefully as the arithmetic.
A quick review should catch an outdated empty-weight record, omitted baggage, duplicated items, wrong station arms, reversed signs, mixed moment scales or a loading entered into the wrong airplane profile. Compare calculator entries with the source records instead of trusting a saved default.
An electronic worksheet can make repeated calculations easier. It still needs correct current aircraft data and the appropriate loading conditions. Work through unfamiliar records or a result outside limits with your instructor before treating the plan as complete.
Check yourself
What is the moment of the fictional 40-pound bag at a positive 95-inch arm, and what are the units?
Show the answer
3,800 lb-in, from 40 lb × 95 in. The result is a moment, not a CG position. It must be combined with the other item moments before dividing by total weight.
A worksheet shows a total moment/1,000 of 88.32 and total weight of 2,000 pounds. Is CG 0.04416 inches?
Show the answer
No. The displayed moment is scaled. Restore it to 88,320 lb-in, then divide by 2,000 lb to obtain 44.16 inches. Keep the scale consistent with the chart or worksheet's instructions.
After burning 120 pounds at the fictional 48-inch fuel arm, is the new CG unchanged because only fuel was removed?
Show the answer
No. Removing 5,760 lb-in as well as 120 lb leaves 82,560 lb-in and 1,880 lb. Their ratio is about 43.91 inches. This moves forward in this example, and it still needs comparison with the applicable limits.
Frequently asked questions
Can I average the arms to find CG?
Not by a simple unweighted average. CG is total moment divided by total weight, so each arm's contribution depends on its item's weight.
Does being below maximum weight mean the airplane is correctly loaded?
No. CG and any separate station or loading restrictions also matter. Use the actual weight-and-balance envelope and limitations for that airplane.
Does fuel burn always move CG aft?
No. The direction depends on where weight is removed relative to CG and on the actual fuel-moment data. Recalculate the applicable flight conditions.
Can FirstSolo.ai approve my loading?
FirstSolo.ai is solely a study tool; it does not issue FAA endorsements or flight approvals. This fictional exercise teaches arithmetic and checks, not operational approval for any airplane.
Sources and review
Last reviewed November 9, 2026.
- PHAK Chapter 10, Weight and Balance: datum, arm, moment, aircraft-specific records, computation and loading checks.
- FAA Weight & Balance Handbook addendum, October 20, 2025: current moment-index explanation; FAA handbook index lists the handbook and addendum.
- 14 CFR 91.9: operating limitations.
- Private Pilot ACS, Task I.F, including S1: weight and balance through all flight phases; current FAA ACS index.
What should you practice next?
Return to the aircraft performance guide, review density altitude, and connect current aircraft records with the airworthiness requirements guide.
Practice performance and limitations on FirstSolo.ai. Explain the datum, each moment, the final units and the applicable limits before accepting a numerical result.

About the author
Ellie Navarro, Student PilotEllie is a student pilot working toward her private pilot certificate in a Cessna 172 near Austin, Texas. She writes up each part of the FAA written the way it finally made sense to her, with the FAA source for every rule.
Last reviewed Nov 9, 2026All guides by EllieKeep going
Start here · PerformanceAircraft Performance: Private Pilot Guide
E6B Practice Problems: 10 Worked Questions
Work 10 original questions on time, fuel, wind correction, density altitude, CG and takeoff charts, then check each method in three answer groups.
Sam Whitaker · Nov 13, 2026 · 9 min read
Takeoff Distance Chart: Step-by-Step Guide
Read chart conditions, separate ground roll from total distance, work a fictional two-input interpolation, and check landing and runway assumptions.
Ellie Navarro · Nov 12, 2026 · 8 min readA fresh question from the FAA references every time, graded by an AI DPE
Start with 50 free credits.
Start free